FabulaTech Forum - Force disconnect doesn't work?

Oct 12^th, 2026, 3:26pm

Welcome, Guest. Please Login or Register.

FabulaTech Forum USB Solutions USB over Network (Moderators: Tim_GaliullinFT, Sergey_Jarovski, Andrew) Force disconnect doesn't work?

Previous topic | Next topic

Pages: 1

Notify of replies

Author

Topic: Force disconnect doesn't work? (Read 9385 times)

Alex
FabulaTech Forum Newbie

Posts: 7

Force disconnect doesn't work?
on: Apr 14^th, 2010, 2:52am

Quote

Modify

Hi!

I've just downloaded the latest version (4.4) and installed on 3 computers specifically to test "force disconnect" feature.

I have 2 clients and 1 server. I've shared the USB device, configured "Allow clients to connect even if occupied...". Rebooted the server (just in case).

Then I connected manually from the client 1. Success. Connected.
Then I tried to connect from client 2. Fail. It says that the device is occupied by client 1.

Tried this both from UI and command line. Same (command line reports error 2404)
Also tried without "Allow ...". Same thing.

My question is what I'm doing wrong? Where is the "force disconnect"?

Best regards,
Alex

IP Logged

Alex_Webster
FabulaTech Forum Senior Member

Gender:

Posts: 257

Re: Force disconnect doesn't work?
Reply #1 on: Apr 16^th, 2010, 12:46am

Quote

Modify

Hello Alex.

Could you please tell what operating systems you have on the client machine and on the server and if it's x32 or x64. Also I need to know what kind of USB device you have.

Please find the new version in the PM, install it and do the following experiment:

Share the device, disable "allow..." feature and connect the device from client#1. Now disconnect it from the client#1 (release it) and connect it using client#2. Check if you can do it. While doing it you need to be sure that nobody works with the device (read/write from it).

Inform me about the results.

IP Logged

Alex
FabulaTech Forum Newbie

Posts: 7

Re: Force disconnect doesn't work?
Reply #2 on: Apr 16^th, 2010, 2:02am

Quote

Modify

Hi,

Server - Win XP Sp2 Eng x86
Client 1 - Win 2k3 R2 Sp2 Eng x86
Client 2 - Win 2k3 R2 Sp2 Eng x86

(All 3 installed on VMWare 7)

Devices - Aladdin eToken Pro 32K (v 4.2B)
Logitech USB Headset
Microsoft Intellimouse

Regarding the version you gave me:
1) The scenario you described does not involve any "force disconnect".
You asked me to "connect, then disconnect, then connect from another PC"
with "allow force disconnect" = off

This scenario does work since v1.0

However, I tried, it also works on 4.5.

2) Now, the most interesting

Force disconnect DOES WORK on 4.5!!!
of course with "allow force disconnect" = on
Connect from client 1, then connect from client 2. Client 1 is being successfully disconnected.

In other words, 4.4 doesn't do "FD" while 4.5 does IN THE SAME CONDITIONS.
Does it bring any light on this issue?

Regards,
Alex

IP Logged

Alex_Webster
FabulaTech Forum Senior Member

Gender:

Posts: 257

Re: Force disconnect doesn't work?
Reply #3 on: Apr 16^th, 2010, 5:20am

Quote

Modify

on Apr 16^th, 2010, 2:02am, Alex wrote:

Regarding the version you gave me:
1) The scenario you described does not involve any "force disconnect".
You asked me to "connect, then disconnect, then connect from another PC"
with "allow force disconnect" = off

This scenario does work since v1.0

However, I tried, it also works on 4.5.

This was the plan, thanks for doing the test. We just wanted to be sure that client#2 could connect the device at all.

on Apr 16^th, 2010, 2:02am, Alex wrote:

In other words, 4.4 doesn't do "FD" while 4.5 does IN THE SAME CONDITIONS.
Does it bring any light on this issue?

Regards,
Alex

So I believe the issue is resolved. You are welcome to use this new version.

IP Logged